How to calculate square footage: rooms, walls and houses

Square footage is area measured in feet, so the calculation is length times width. A 12-foot by 12-foot room is 144 square feet. Every other shape on this page is that same rule used more than once: split the shape into rectangles, work out each one, add them up.

Measure in feet before you multiply

A common way to get the wrong answer is mixing inches into a feet calculation. Convert first, dividing inches by 12.

Measurement Conversion Decimal feet
10 ft 6 in 6 ÷ 12 = 0.5 10.5 ft
7 ft 9 in 9 ÷ 12 = 0.75 7.75 ft
4 ft 2 in 2 ÷ 12 = 0.1667 4.1667 ft

A 3 ft 6 in by 4 ft 2 in opening is 3.5 × 4.1667, or 14.58 square feet. Rounding the 4 ft 2 in to 4 ft first gives 14, which is about 0.6 square feet short.

If both measurements are already in inches, multiply them and divide by 144. A 96 in by 120 in area is 11,520 ÷ 144 = 80 square feet.

A rectangular room

Multiply the two sides. A room 14 ft by 11 ft is 14 × 11 = 154 square feet.

Measure wall to wall at floor level, between the inside faces of the walls. Add closets and alcoves the flooring will run into as separate rectangles. That is your floor area. Paint needs wall area instead, which is the section after next.

Buy extra for cuts and waste. The amount depends on the layout and the product, so check the percentage the manufacturer recommends for what you are installing.

An L-shaped room

An L is two rectangles sharing an edge. Find the line where one wall length changes, split the shape there, and add the two areas.

Section Dimensions Area
Main part 14 ft × 11 ft 154 sq ft
Leg 8 ft × 6 ft 48 sq ft
Total 202 sq ft

The same idea handles any shape built from straight walls. A T, a U and a stepped wall are all rectangles once you decide where to cut them.

To total several rooms and subtract cut-outs in one go, use the square footage calculator. It converts between square feet, square yards, square meters and acres.

A wall with a door or window

Wall area is the gross wall minus the openings, because you are not covering the door or the glass.

Item Dimensions Area
Wall 12 ft long × 8 ft high 96 sq ft
Subtract door 3 ft × 7 ft −21 sq ft
Subtract window 4 ft × 4 ft −16 sq ft
Paintable wall 59 sq ft

Measure the part you are leaving unpainted: the door or window, including its frame if you are not painting the frame.

For a whole room, find each wall this way and add them, or multiply the perimeter by the ceiling height and subtract every opening. A 14 ft by 11 ft room with an 8 ft ceiling has a perimeter of 14 + 11 + 14 + 11 = 50 ft, so 50 × 8 = 400 square feet before you take off the openings. That is the area for one coat.

An irregular shape

For a shape with straight edges and odd angles, split it into rectangles and triangles. A triangle is half of a rectangle that would enclose it, so its area is base × height ÷ 2, with the height measured straight up from the base rather than along the slanted side.

For a circle, multiply the radius by itself and by 3.14. A round room 10 ft across has a 5 ft radius: 3.14 × 5 × 5 = 78.5 square feet. Halve that for a half circle.

For a trapezoid, average the two parallel sides and multiply by the height between them. A shape with parallel sides of 10 ft and 6 ft, 4 ft apart, is (10 + 6) ÷ 2 × 4 = 32 square feet.

For anything else, divide the space into rectangles and triangles that follow the walls, measure each, and add. A boundary that curves without being a circle is the one case a tape measure cannot settle, because wrapping a single rectangle around it overstates the area badly. Bring in a survey or a calculating tool.

Square feet into other units

Convert Do this Example
Square feet to square yards Divide by 9 144 sq ft = 16 sq yd
Square feet to square meters Multiply by 0.09290304 100 sq ft = 9.29 sq m
Square feet to acres Divide by 43,560 43,560 sq ft = 1 acre

Why your number differs from the listing

If you measure a house room by room from the inside and add the rooms up, you may well get a smaller figure than the one on a listing. One common reason is the wall. The figure a lender reports is measured to the outside face of the exterior walls, so it includes the thickness of the walls themselves. An interior room-by-room sum stops at the inside face of each wall and leaves that thickness out.

The gap is not small. A house that measures 30 ft by 40 ft on the outside is about 29 ft by 39 ft on the inside, allowing for 6 in walls, so the interior figure is roughly 1,131 square feet against 1,200 outside.

Three other causes:

  • Your measurement may include a space the standard leaves out, such as a finished basement or a garage.
  • The figure you are comparing against may have been calculated from building plans, or from exterior dimensions without anyone inspecting the interior.
  • Listing figures are not always measured to this standard at all. They can come from tax records, builder plans or an earlier appraisal, and some include a finished basement.

So settle which source a figure came from before treating it as wrong. Ask the agent what the number counts. If you need an official figure, an appraiser or a measuring professional who works to the standard below can supply one.

A whole house: the standard behind the number

A house’s listed square footage is not the sum of its rooms. It follows a published standard, ANSI Z765.

ANSI Z765, Square Footage: Method for Calculating, is a voluntary American National Standard for measuring finished floor area in single-family houses. It dates from 1996 and is maintained by Home Innovation Research Labs. It does not apply to apartments or multifamily buildings, so it will not tell you how a rental or a condo unit is measured.

You may also see the above-grade figure called gross living area (GLA) on an appraisal.

How the standard measures a house

  1. Measure each level from the outside. Finished area is the sum of finished areas on a level, “measured at floor level to the exterior finished surface of the outside walls.” You are measuring to the outside face of the wall, not the inside.
  2. Break each level into rectangles where the footprint steps in or out, and add them.
  3. Add the above-grade levels together. That total is the figure lenders report.
  4. Report below-grade area separately. A level counts as below grade if it is wholly or partly below grade.
  5. Report the final figure to the nearest whole square foot.

For attached houses such as townhouses, the standard measures to the center line of the shared wall.

What counts and what does not

Counts toward above-grade finished area

  • Finished rooms and finished areas on levels entirely above grade
  • Ceilings at least 7 ft high, or 6 ft 4 in under beams and ducts
  • Sloped ceilings where at least half the room is 7 ft or higher
  • Staircases, counted on the level they descend from

Does not count

  • Garages, attached or detached
  • Unfinished areas, such as bare studs or a bare concrete floor
  • Porches, decks and patios that are not enclosed or not suitable for year-round use
  • Any part of a room with less than 5 ft of headroom
  • The opening to a floor below, such as a two-story foyer

A basement, finished or not, is reported on its own line as below-grade area. It is never added to the above-grade figure. The standard is explicit: “No statement of a house’s finished square footage can be made without the clear and separate distinction of above-grade areas and below-grade areas.”

A worked house

Two floors, each 40 ft by 30 ft measured on the outside. A 12 ft by 10 ft open-to-below foyer on the second floor, with no stairs in it. An attached 22 ft by 22 ft garage. A finished 40 ft by 30 ft basement.

Area Calculation Result In the above-grade figure?
First floor 40 × 30 1,200 sq ft Yes
Second floor 40 × 30 1,200 sq ft Yes
Less foyer opening 12 × 10 −120 sq ft No, an opening to the floor below
Second floor, net 1,200 − 120 1,080 sq ft Yes
Above-grade finished area 1,200 + 1,080 2,280 sq ft
Finished basement 40 × 30 1,200 sq ft No, below grade, reported separately
Attached garage 22 × 22 484 sq ft No

A listing that adds everything would show 3,964. The above-grade figure is 2,280.

The calculator adds the areas you enter. It does not decide what counts under ANSI Z765, so settle that first.

Where the standard comes from

The standard’s own foreword says that “before the original adoption of this Standard in 1996, no national standard existed in the United States for measuring square footage in single-family houses.”

Fannie Mae has required ANSI Z765-2021 for applicable appraisals on loans it buys since April 1, 2022. That covers single-family homes where the appraiser inspects the inside and outside (Fannie Mae’s 2022 letter to the National Association of Realtors, and the Appraisal Institute’s report on the change). Freddie Mac followed on November 2, 2023. Fannie Mae calls it the most widely used home measurement standard in the United States.

Zillow’s measuring guide tells readers “there’s no established standard for measuring a residential property, and everyone seems to measure square footage of a house differently.” There is one, and it has been in place since 1996.

Common questions

How many square feet is a 12x15 room? 180 square feet.

How do I convert inches to square feet? Multiply the inches together and divide by 144. A 96 in by 120 in area is 80 square feet.

Is the garage included in square footage? Not in finished square footage. ANSI Z765 excludes garages from finished area. Some listings show total area under the roof instead, so check what the figure counts.

Does a finished basement count? Not in the above-grade figure. It is reported separately as below-grade finished area, which is also how it should be read on a listing.


The standard itself is voluntary. Fannie Mae and Freddie Mac require it for the appraisals described above, and Fannie Mae has said some state and local jurisdictions require it too. This is a measurement guide, not an appraisal or a valuation of any property.

If you would rather not run the arithmetic by hand, the square footage calculator adds rooms and shapes, subtracts cut-outs and converts between square feet, square yards, square meters and acres.

More articles · Spotted a mistake? Tell us.